Attach the keyboard. Page Removing and replacing a FRU 6. Secure the keyboard bezel from the underside of the computer with the screw d. This screw cannot be fastened properly without attaching keyboard. Page Mini Pci Adapter Plug the gray cable to jack M, and the black cable to jack A. Insert the notched end of the card into the socket, and then press the card firmly. Pivot the card until it snaps into place.
Page Fan Assembly Then slightly push the tool into the gap until the fan assembly comes off. Do not move the tool upward or downward to remove the fan assembly between the gap. Page Step 2a is for the fan assembly, long and for the fan assembly, long M Step 2b is for the fan assembly, short. Distortion of the fan assembly may cause a thermal problem. Page Removing and replacing a FRU When installing: v Before you attach the fan assembly to the computer, apply thermal grease on the part marked a as in the following figures.
Page Speaker Assembly 2 2. When installing: Make sure that the connector 4 is firmly attached. Then route the cable as in 3. Page Keyboard Bezel When installing: Make sure that all the latches marked a are firmly attached.
Lcd Models Page Lcd Assembly Then detach the LCD connector 4. When installing: Make sure that the bracket 3 and the connector 4 are firmly attached, and then secure them with the screw. When installing: Make sure that the antenna cables are correctly routed and securely in place. Page Removing and replacing a FRU When installing: Make sure that the security keyhole which is on the left-rear corner of the base cover and the keyhole of the bracket inside are aligning firmly.
Page Cpu 1 to release the lock; then remove the CPU 2. Page 2. Separate the Ultrabay Slim guide rail assembly a and the hard disk drive guide rail b. Page 0. Page Important notice for handling the system board: The security chip a is soldered on the underside of the system board as in this figure.
Page Removing and replacing a FRU Before removing the system board, remove the support structure a and the cable guide b. When installing: Make sure that the connectors 2 are firmly attached to the system board. Step Screw quantity Color Torque Page 1 2. Page FCC labels on it, find the same one from the label kit and stick it on the new base cover.
Stick the labels on the new base cover as shown in this figure. Page Cover Page e together. When installing: Attach the system board so that the two small projections on the base cover fit into the holes provided, and then secure the system board with the screw. Page Lcd Front Bezel Page Inverter Card For the other models, skip step 1 to 5.
Page In step 6 , remove the latch bar as in this figure. Lift the latch bar in the direction of the arrow 7 , and then remove the left latch in the direction of the arrow 8. Page 10b. Then remove the LCD panel in the direction of arrow Then detach the connector 16 in the direction of the arrow.
Attach the left latch to the LCD cover. Paste three gaskets only for the models with Bluetooth wireless features. For the other models, skip this step. Page Removing and replacing a FRU d. Coil the spiral tube round the antenna cables 6. Slide the spiral tube in the direction shown by arrow 7. Make sure that the antenna cable is not pinched by cable clip a.
Secure the LCD panel with the screws. At the parts indicated by arrows a , the antenna cables go through the hinges. When you route the antenna cables, attach the cables firmly. Page For the other models, skip this step. Do not route the cable over the bracket. To do so, the cable might be pinched between the LCD front bezel and the LCD cover, and the cable or the other parts might be damaged or might not be installed properly.
When you route the cables around the LCD hinges, do as shown in c. Page Make sure that the system lock key A is set to the Unlock position. Release the front latches in step 4 , and then remove the top cover 5.
Then detach the connector cable 6 as in the figure. Page Parts list No. Keyboard bezel assembly FRU Battery pack, Li-ion 9 cell 7.
They are not CRUs in the Page Lcd Frus Parts list Xga Tft Inverter card, Page In. FRU Inverter card, Xga Tft Parts list Page Keyboard Parts list Keyboard Keyboards for Page Parts list Keyboards for Page Parts list System miscellaneous parts Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used.
This manual is also suitable for: Thinkpad t43p Dock ii Thinkpad dock ii. Print page 1 Print document pages. Rename the bookmark. Offerings for all customer segments: small, Print page 1 Print document 18 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Removing and replacing a FRU … Plug the gray cable to jack M, and the black cable to jack A.
Insert the notched end of the card into the socket, and then press the card firmly. Pivot the card until it snaps into place. Make sure that it is firmly fixed in the slot and does not move easily. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.
0コメント